Permacolor PermaGard Dry-Erase Overlaminate [1mil, 54" x 150', High-Gloss Clear]

This Permacolor PermaGard 54" x 150' Gloss Clear Dry-Erase Overlaminate is a gloss clear 1-mil polyester film top-coated on one side for perfect dry-erase capabilities and on the other with a permanent clear acrylic pressure sensitive adhesive, recommended for indoor and outdoor use. The adhesive is protected by a 78# white Kraft release liner that provides for easy liner removal and a smooth adhesive surface. This film is designed for use over digitally produced images by solvent inkjet, eco-solvent inkjet, UV inkjet and water-based inkjet (pigmented and dye), electrostatic and thermal transfer resin ribbons to impart protection from abrasion, moisture, and other potentially damaging effects in both indoor and outdoor environment. Turn any graphic into an interactive dry-erase piece with Permacolor PermaGard 1mil 54" x 150' Gloss Clear Dry-Erase Overlaminate.

• Features and Benefits:
  • Suitable for use over solvent, eco-solvent, UV and latex printed wide-format graphics
  • Up to four years outdoor durability
• Typical Uses:
  • Protection of short-term indoor and outdoor graphics
• Use with: IMAGin PrintVinyl, JT5800 and REBEL RB200 Series


• Physical Properties
  

  Property	Typical Values	Test Method
  Thickness, inches (µm) Film plus adhesive Total product	0.0040 (101) 0.0055 (139)	ASTM-D645
  Quick Tack, lb./in² (N/25mm) Stainless Steel	1.5 (6.5)	Mactac CTM-25
  Peel Adhesion lb./in. (N/25mm) Stainless Steel - 30 min - 24 hrs.	2.5 (11) 2.8 (12.25)	Mactac CTM-21 48 hours @ 158°F (70°C) Bonded to aluminum (Method D)
  Dimensional Stability, inches (mm) MD CD	0.02 (0.5) 0.02 (0.5)	FTM-14
  Gloss (60° angle) Gloss Lustre Matte	88 50 8	ASTM D-523
  Temperature Range Application: End Use:	Above 45°F (16°C) -20° to 150°F (-28° to 66°C)
  Adhesive pH	Neutral	TAPPI-529

• Durability
  The durability of the film is up to 4 years outdoors and 5+ years indoors. The durability of the image is mainly dependent upon the quality of the inks (see technical data sheets given by the ink manufacturers) and pressure sensitive media being used.
• Shelf Life
  Two years when stored at 75°F (24°C) and 50% relative humidity or less. Note: Mactac recommends that rolls be stored on end or suspended from the core.
• Limitations
  1) The user is responsible for determining the product’s suitability, including adhesion and if needed, removal characteristics when used in applications other than listed specifically in this Performance Guide.
  2) If there are any questions about applications, please contact your Mactac sales representative to discuss your requirements for recommendations.
  3) If this is a printed Performance Guide it is an uncontrolled document. Please check the Mactac website for the latest, most up-to-date version.
  
• Recommendations
  
  • Where exposure to moisture, chemicals, solvents or high pressure wash is anticipated, Mactac recommends sealing the edges with varnish, silicone or other sealant to prevent penetration by these liquids.
  • Overlaminates should not be applied onto dusty or dirty prints.
  • The mounting board must be properly prepared prior to mounting the image. This may include wiping with alcohol, light sanding or surface sealing depending on the board. Contact your board supplier for their recommendation.
  • Mactac's pressure sensitive mounting films are intended for "Cold Roll Lamination" (40°F - 104°F). The addition of heat while simultaneous mounting with Thermal Overlaminates may result in curl or have other detrimental effects on the finished product.
  • Whenever possible, always test first to ensure end-use capability.
  
  • Values given are typical for unprocessed product and are not for use as specifications. Processing may change the values.